Classification Of Drilling Tools

1. Reaming drill. Reaming drills have 3 to 4 teeth and are more rigid than twist drills to expand existing holes and improve dth drilling tools accuracy and finish. 

2. Drilling. The boring drill has a large number of teeth, and the hole end is processed into a desired shape by a forming method for processing of dth drilling tools factory the countersunk holes of various countersunk screws or flattening the outer end faces of the holes. 

3. Center drill. The center drill is used for drilling the center hole of the shaft type workpiece. It is essentially a composite of twist drill and boring drill with a small helix angle, so it is also called a composite center drill.

4. Twist drill. It consists mainly of the working part and the handle. The working part has two spiral grooves that are shaped like twists. In order to reduce the friction between the guiding portion and the wall of the hole during drilling, the twist drill is gradually reduced in diameter toward the shank and has an inverted cone shape.

5. Flat drill. The cutting part has a spade shape, a simple structure, a low manufacturing cost, and the cutting fluid is easily introduced into the hole, but the cutting and chip discharging performance is poor. The structure of the flat drill is both integral and assembled. The monolith is mainly used for drilling micropores with a diameter of 0.03 to 0.5 mm. The assembled flat drill blade is replaceable and can be internally cooled. It is mainly used for drilling large holes with a diameter of 25 to 500 mm.

6. Deep hole drilling. It usually refers to a tool that machines a hole with a hole depth to hole ratio greater than 6. Commonly used are gun drills, BTA deep hole drills, jet drills, DF deep hole drills, etc. Nesting drills are also commonly used for deep hole machining in dth drilling tools manufacturer.

DTH Drilling Tools
DTH Drilling Tools

评论

发表评论

此博客中的热门博文

The Things Of Drilling Driver Should Note

图片
Let us learn about some things of drilling driver should note! 1. DTH drill driver must abide by the mine "General Safety Operation Procedures for Post Work". 2. DTH drill drivers must abide by the safety regulations for commuting cars and hosting. 3. DTH drill drivers must comply with the safety regulations for the management of the cannon, the edge of the steps and the day of the run.  4. When moving the  DTH drill bits  or replacing the drill pipe, we should pay close attention to the high voltage line around it so as not to touch it. 5. When checking and handling cable and other electrical faults, the drop switch must be removed. 7. When working on a large shelf for high-altitude work, you must wear a safety helmet and a guardian, and you are not allowed to stand under the large shelf. 8. Thunderstorms and windy days are prohibited from working on high. We are  DTH drilling tools supplier , welcome to contact us!
阅读全文

The Features Of Roller Cone Bit

图片
Let's take a look at the features of  roller cone bit . 1. The use of high-strength and high-toughness alloy teeth makes it improve the resistance of the teeth to impact, reduce the chance of broken teeth, and the soft formation is equipped with a spoon-shaped tooth. 2. A layer of the hard alloy is placed on the bearing of the tooth, and the roller bearing is also silver plated so that the bearing has improved the ability to resist seizure and load. 3. The O-ring seal adopts a more wear-resistant high-saturated nitrile rubber, which increases the cross-section of the seal ring, and increases the sealing small boss at the outer end of the seal area to improve the reliability of the seal. 4. the use of steel ball locking cone, can be suitable for relatively high speed. 5. The number of teeth to be optimized and the equipment such as the tooth and the alloy tooth can maximize the cutting and speed of the drill. 6. the use of a new production of grease that can withstand t
阅读全文

Development Trend Of Hydrodynamic DTH Hammer

图片
Hydraulic hammer drilling has turned out to be an innovative drilling technique to deal with hard and complicated rock formations through numerous developments and practices. A variety of hydraulic  DTH hammer  has shaped a new type of hole-bottom machine and will be more in-depth and greater degree of development. First of all, together with the evolution of high technologies and digital technologies, the theoretical research level of impact rotary drilling will have a fantastic breakthrough, the expressions of their mechanical components of the hammer and the moving portions of the hydraulic hammer with different structure types will likely be improved and enriched, and the structure and parameter layout of the hydraulic hammer will likely be further simplified, optimized and scientific by computer simulation. The evaluation way of the operating parameters of the hydraulic hammer will probably be more precise, intuitive and intelligent, and the new innovative technical detector
阅读全文